FDI August 2022

Written by R.W. Baird analyst David J. Manthey, CFA with Quinn Fredrickson, CFA 9/9/22 Key Takeaway: The August seasonally adjusted Fastener Distributor Index (FDI) bounced back nicely from last month’s sub-50 reading, increasing back into expansionary territory at 52.6. This was consistent with a still very positive FLI reading last month. Demand commentary seemed to […]

Continue Reading…

FTM 179: Can the sulphur % in steel be too high?

This edition of the Fastener Training Minute with Carmen Vertullo was originally published August 18th, 2022 as “the chemical analysis requirements for SAE J429 fasteners, in particular Grade 5“, during episode 179 of Fully Threaded Radio. Hi everyone this is Carmen Vertullo coming to you from the Fastener Training Institute and the AIM Testing Laboratory […]

Continue Reading…

FTM 178: Do drawings always reduce risk?

This edition of the Fastener Training Minute with Carmen Vertullo was originally published July 21st, 2022 as “Do drawings always reduce the risk of producing a good fastener?” during episode 178 of Fully Threaded Radio. Well, hello everyone this is Carmen Vertullo with the Fastener Training Minute coming to you from AIM Testing Laboratory, in […]

Continue Reading…

FDI June 2022

Written by R.W. Baird analyst David J. Manthey, CFA with Quinn Fredrickson, CFA 7/7/22 Key Takeaway: The June seasonally adjusted Fastener Distributor Index (FDI) reading is 53.8, improved vs. last month, indicating slightly faster growth than May. The pricing indices moderated some (albeit remaining at elevated levels) as respondents noted softening commodity prices and some […]

Continue Reading…

FDI May 2022

Written by R.W. Baird analyst David J. Manthey, CFA with Quinn Fredrickson, CFA 6/7/22 Key Takeaway: The May seasonally adjusted Fastener Distributor Index (FDI) was essentially unchanged vs. last month, remaining in modest growth territory at 52.7. Container/import logistics constraints and slowing growth were consistent themes among respondents. The pricing indices were also stable but […]

Continue Reading…

FDI April 2022

Written by R.W. Baird analyst David J. Manthey, CFA with Quinn Fredrickson, CFA 5/6/22 Key Takeaway: The April seasonally adjusted Fastener Distributor Index (FDI) dipped to 52.6, lower m/m, primarily on softer selling conditions. The overwhelming theme among participants commentary and across the various components of the FDI was growth but slowing growth amid material […]

Continue Reading…

FDI March 2022

Written by R.W.Baird analyst David J. Manthey, CFA with Quinn Fredrickson, CFA 4/6/22 Key Takeaway: The March seasonally adjusted Fastener Distributor Index (FDI) saw a modest m/m improvement at 57.2 on better sales and employment levels. Despite a slightly weaker reading in the supplier deliveries index amid some manufacturing plant shutdowns in Asia and continued […]

Continue Reading…

FTM 174: How tight is too tight for a Nylon Insert Locknut?

This edition of the Fastener Training Minute with Carmen Vertullo was originally published March 17th, 2022 as “How tight is too tight for a Nylon Insert Locknut?” during episode 174 of Fully Threaded Radio. Hello everyone this is Carmen Vertullo with the Fastener Training Minute coming to you from the Fastener Training Institute and AIM […]

Continue Reading…

FDI February 2022

Written by R.W.Baird analyst David J. Manthey, CFA with Quinn Fredrickson, CFA 3/7/22 Key Takeaway: The February Fastener Distributor Index (FDI) recovered nicely m/m, rebounding to 56.0, following January’s seasonal-adjustment driven down-tick. The recovery was broadly consistent with recovery seen in the ISM PMI and other macroeconomic data points as pandemic-related disruption eased. Respondent commentary […]

Continue Reading…

FTM 173: How do I install Jam Nuts?

This edition of the Fastener Training Minute with Carmen Vertullo was originally published February 16th, 2022 as “How do I install jam Nuts?” during episode 173 of Fully Threaded Radio. Well hi everyone, this is Carmen Vertullo with the Fastener Training Minute coming to you from the Fastener Training Institute and the AIM Testing Laboratory […]

Continue Reading…

Share via
Copy link
Powered by Social Snap