This edition of the Fastener Training Minute with Carmen Vertullo was originally published May 19, 2016 as “The ASTM F16 Fastener Technical Committee” during episode 105 of Fully Threaded Radio. Hi everybody, this is Carmen Vertullo with the Fastener Training Minute. Today I’m not coming to you from the Carver FACT Center in San Diego, […]
Read More… from FTM 105: ASTM F16 Fastener Technical Committee
This edition of the Fastener Training Minute with Carmen Vertullo was originally published April 22, 2016 as “books for your technical library” during episode 104 of Fully Threaded Radio. Well, hi everybody, this is Carmen Vertullo from the Fastener Training Institute bringing you the Fastener Training Minute from the Carver FACT Center here in beautiful […]
This edition of the Fastener Training Minute with Carmen Vertullo was originally published March 17, 2016 as “can stainless steel be magnetic?” during episode 103 of Fully Threaded Radio. Well, this is Carmen Vertullo with your Fastener Training Minute coming from the Carver FACT Center in San Diego. And of course representing the Fastener Training […]
This edition of the Fastener Training Minute with Carmen Vertullo was originally published February 18, 2016 as “Why did a Grade 8 Flange Head Bolt break?” during episode 102 of Fully Threaded Radio. Well hi everybody, I don’t know what time it is when you’re listening to this but it’s like zero dark thirty here […]
Read More… from FTM 102: Why did a Grade 8 Flange Bolt break?
This edition of the Fastener Training Minute with Carmen Vertullo was originally published December 16, 2015 as “A question about thread acceptability” during episode 100 of Fully Threaded Radio. Hi everybody. This is Carmen Vertullo from Carver Consulting and the Fastener Training Institute with the Fastener Training Minute. Today I went deep into the archives […]
Read More… from FTM 100: My Tri-Roll gauge rejects a thread the supplier says is OK
This edition of the Fastener Training Minute with Carmen Vertullo was originally published November 19, 2015 as “another war Story about socket set screws” during episode 99 of Fully Threaded Radio. Hi, everybody, this is Carmen Vertullo with the Fastener Training Minute brought to you by Fastener Training Institute and Carver Consulting. If you’ve been […]
Read More… from FTM 99: Where should I NOT use socket set screws?
This edition of the Fastener Training Minute with Carmen Vertullo was originally published October 29, 2015 as “another war Story about socket set screws” during episode 98 of Fully Threaded Radio. Hi everybody, this is Carmen Vertullo with the Fastener Training Minute brought to you by the Fastener Training Institute and my little place out […]
Read More… from FTM 98: “daddy where do drawings come from?”
This edition of the Fastener Training Minute with Carmen Vertullo was originally published September 17, 2015 as “Do we really need to produce technical drawings?” during episode 97 of Fully Threaded Radio. Hi everybody, this is Carmen Vertullo from Carver Consulting with the Fastener Training Minute, and today I want to talk to you about […]
Read More… from FTM 97: Do we really need to produce technical drawings?
This edition of the Fastener Training Minute with Carmen Vertullo was originally published August 20, 2015 as “The Wedge Tensile Test” during episode 96 of Fully Threaded Radio. Hi everybody, this is Carmen Vertullo with the Fastener Training Institute and Carver Consulting bringing you the Fastener Training Minute. I’ve had a couple of inquiries from […]
This edition of the Fastener Training Minute with Carmen Vertullo was originally published July 23, 2015 as “interview with Carmen Vertullo” during episode 95 of Fully Threaded Radio. (Eric Dudas) Everyone who listens to Fully Threaded Radio is very familiar with Carmen Vertullo. We’ve been playing the Fastener Training Minute segment for last few months, […]