FTM 186: Can black oxide treated stainless rust?

This edition of the Fastener Training Minute with Carmen Vertullo was originally published March, 16th, 2023 as “Why did screws made of 18-8 stainless steel that were passivated and black oxide finished rust in a salt spray test?” during episode 186 of Fully Threaded Radio. Hello everybody, this is Carmen Vertullo with your Fastener Training […]

Continue Reading…

FTM 185: approved coatings for structural bolts

This edition of the Fastener Training Minute with Carmen Vertullo was originally published February, 17th, 2023 as “What are the approved coatings for structural bolts during episode 185 of Fully Threaded Radio. Well hi everyone, welcome to the Fastener Training Minute. This is Carmen Vertullo coming to you from the Fastener Training Institute and from […]

Continue Reading…

FTM 184: Why do we salt spray test stainless steel

This edition of the Fastener Training Minute with Carmen Vertullo was originally published January, 17th, 2023 as “Why do we salt spray test stainless steel” during episode 184 of Fully Threaded Radio. Well hello everyone this is Carmen Vertullo with the Fastener Training Minute coming to you from beautiful El Cajon California, the location of […]

Continue Reading…

FTM 182: How do you tighten stainless bolts

This edition of the Fastener Training Minute with Carmen Vertullo was originally published November, 18th, 2022 as “How to develop good methods for tightening stainless steel structural bolting” during episode 182 of Fully Threaded Radio. Well hello everyone, this is Carmen Vertullo with your Fastener Training Minute coming to you from beautiful El Cajon California, […]

Continue Reading…

FTM 181: Should bolts stretch under load

This edition of the Fastener Training Minute with Carmen Vertullo was originally published October, 27th, 2022 as “How to develop good methods for tightening stainless steel structural bolting” during episode 181 of Fully Threaded Radio. Well, hi everybody. This is Carmen Vertullo with the Fastener Training Minute, coming to you from the Fastener Training Institute […]

Continue Reading…

FTM 178: Do drawings always reduce risk?

This edition of the Fastener Training Minute with Carmen Vertullo was originally published July 21st, 2022 as “Do drawings always reduce the risk of producing a good fastener?” during episode 178 of Fully Threaded Radio. Well, hello everyone this is Carmen Vertullo with the Fastener Training Minute coming to you from AIM Testing Laboratory, in […]

Continue Reading…

FTM 174: How tight is too tight for a Nylon Insert Locknut?

This edition of the Fastener Training Minute with Carmen Vertullo was originally published March 17th, 2022 as “How tight is too tight for a Nylon Insert Locknut?” during episode 174 of Fully Threaded Radio. Hello everyone this is Carmen Vertullo with the Fastener Training Minute coming to you from the Fastener Training Institute and AIM […]

Continue Reading…

FTM 173: How do I install Jam Nuts?

This edition of the Fastener Training Minute with Carmen Vertullo was originally published February 16th, 2022 as “How do I install jam Nuts?” during episode 173 of Fully Threaded Radio. Well hi everyone, this is Carmen Vertullo with the Fastener Training Minute coming to you from the Fastener Training Institute and the AIM Testing Laboratory […]

Continue Reading…

FTM 172 – are my fasteners RoHS compliant?

This edition of the Fastener Training Minute with Carmen Vertullo was originally published January 18th, 2022 as “are my fasteners RoHS compliant?” during episode 172 of Fully Threaded Radio. Well, hi everybody, this is Carmen Vertullo with the Fastener Training Minute. Coming to you from the Fastener Training Institute in beautiful El Cajon, California where […]

Continue Reading…