This edition of the Fastener Training Minute with Carmen Vertullo was originally published March, 18th 2024 as “how do I know if an installed bolt has been properly tightened?” during episode 198 of Fully Threaded Radio. Well hello everyone, this is Carmen Vertullo with your Fastener Training Minute, coming to you from Fastener Training Institute […]
Read More… from FTM 198 – how do I know if a bolt has been properly tightened?”
This edition of the Fastener Training Minute with Carmen Vertullo was originally published June, 22nd, 2023 as “Can you recover fasteners that have hydrogen embrittlement, and should you?” during episode 189 of Fully Threaded Radio. Well hi everybody, this is Carmen Vertullo with the Fastener Training Minute coming to you from the Fastener Training Institute […]
Read More… from FTM 189: Can we recover hydrogen embrittlement?
This edition of the Fastener Training Minute with Carmen Vertullo was originally published April, 18th, 2023 as “We have a fastener, our ring gauge says it is OK, the customer’s ring gauge says it doesn’t conform. What do we do?” during episode 187 of Fully Threaded Radio. Well hi everybody, this is Carmen Vertullo with […]
Read More… from FTM 187: What happens when ring gauges don’t agree
This edition of the Fastener Training Minute with Carmen Vertullo was originally published August 31, 2017, as “the difference between a hex bolt and a hex cap screw” during episode 119 of Fully Threaded Radio. Hi everybody, this is Carmen Vertullo with your Fastener Training Minute from the Fastener Training Institute and the Carver FACT […]
This edition of the Fastener Training Minute with Carmen Vertullo was originally published July 21, 2016 as “can stainless steel be magnetic?” during episode 107 of Fully Threaded Radio. Well, hi everybody, it’s Carmen Vertullo with your Fastener Training Minute coming to you from Carver Engineering and Manufacturing, the Carver FACT Center here in San […]
Read More… from FTM 107: How do you hire a quality engineer?
This edition of the Fastener Training Minute with Carmen Vertullo was originally published April 22, 2016 as “books for your technical library” during episode 104 of Fully Threaded Radio. Well, hi everybody, this is Carmen Vertullo from the Fastener Training Institute bringing you the Fastener Training Minute from the Carver FACT Center here in beautiful […]
This edition of the Fastener Training Minute with Carmen Vertullo was originally published March 17, 2016 as “can stainless steel be magnetic?” during episode 103 of Fully Threaded Radio. Well, this is Carmen Vertullo with your Fastener Training Minute coming from the Carver FACT Center in San Diego. And of course representing the Fastener Training […]
This edition of the Fastener Training Minute with Carmen Vertullo was originally published February 18, 2016 as “Why did a Grade 8 Flange Head Bolt break?” during episode 102 of Fully Threaded Radio. Well hi everybody, I don’t know what time it is when you’re listening to this but it’s like zero dark thirty here […]
Read More… from FTM 102: Why did a Grade 8 Flange Bolt break?
This edition of the Fastener Training Minute with Carmen Vertullo was originally published December 16, 2015 as “A question about thread acceptability” during episode 100 of Fully Threaded Radio. Hi everybody. This is Carmen Vertullo from Carver Consulting and the Fastener Training Institute with the Fastener Training Minute. Today I went deep into the archives […]
Read More… from FTM 100: My Tri-Roll gauge rejects a thread the supplier says is OK
This edition of the Fastener Training Minute with Carmen Vertullo was originally published November 19, 2015 as “another war Story about socket set screws” during episode 99 of Fully Threaded Radio. Hi, everybody, this is Carmen Vertullo with the Fastener Training Minute brought to you by Fastener Training Institute and Carver Consulting. If you’ve been […]
Read More… from FTM 99: Where should I NOT use socket set screws?