FTM 165: Why can’t I get low strength socket cap screws?

Fastener Training Minute, Episode 165

This edition of the Fastener Training Minute with Carmen Vertullo was originally published June 19, 2021 as “Why is it that ASTM A574 socket screws do not require a mark, and what about Grade 8 socket head cap screws? ” during episode 165 of Fully Threaded Radio. Well hello everyone. This is Carmen Vertullo with […]

Read More… from FTM 165: Why can’t I get low strength socket cap screws?

FTM 164: When can I substitute product?

Fastener Training Minute: Episode 164

This edition of the Fastener Training Minute with Carmen Vertullo was originally published May 12, 2021 as “When can I substitute one product for another product” during episode 164 of Fully Threaded Radio. Well, hi everybody. This is Carmen Vertullo with your Fastener Training Minute coming to you from the Fastener Training Institute and the […]

Read More… from FTM 164: When can I substitute product?

FTM 163: What is a reduced load ability head

Fastener Training Minute: Episode 163

This edition of the Fastener Training Minute with Carmen Vertullo was originally published April 15, 2021 as “What is a reduced load ability head” during episode 163 of Fully Threaded Radio. Well, hi everybody, this is Carmen Vertullo with the Fastener Training Minute, coming to you from the Fastener Training Institute and the AIM Testing […]

Read More… from FTM 163: What is a reduced load ability head

FTM 162: What is A36 Threaded Rod

Fastener Training Minute 162: What is A36 threaded rod

This edition of the Fastener Training Minute with Carmen Vertullo was originally published March 19, 2021 as “What is A36 threaded rod” during episode 162 of Fully Threaded Radio. Well, hi everyone. This is Carmen Vertullo with your Fastener Training Minute coming to you from the Fastener Training Institute and AIM Testing Laboratory in beautiful […]

Read More… from FTM 162: What is A36 Threaded Rod

FTM 161: Passivation, what is it?

What is passivation

This edition of the Fastener Training Minute with Carmen Vertullo was originally published February 18, 2021 as “Passivation. What it is, what it isn’t, why it matters to us” during episode 161 of Fully Threaded Radio. Well, hello everyone. Welcome to the Fastener Training Minute. This is Carmen Vertullo coming to you from the Fastener […]

Read More… from FTM 161: Passivation, what is it?

FTM 160: Good and bad Nuts

how to tell if a nut is a good nut or  a bad nut.

This edition of the Fastener Training Minute with Carmen Vertullo was originally published January 23, 2021 as “how to tell if a nut is a good nut or  a bad nut” during episode 160 of Fully Threaded Radio. Well, welcome to the Fastener Training Minute brought to you by the Fastener Training Institute and the […]

Read More… from FTM 160: Good and bad Nuts

FTM 159: Thread Run-Out

Fastener Training Minute 159: Thread run-out

This edition of the Fastener Training Minute with Carmen Vertullo was originally published December 16, 2020 as “how do we measure thread pitch run-out during episode 159 of Fully Threaded Radio. Well, hi everyone, this is Carmen Vertullo with the Fastener Training Minute, coming to you from the Fastener Training Institute and the AIM Testing […]

Read More… from FTM 159: Thread Run-Out

FTM 158: What’s the Point?

Fastener Training Minute 158: What's the Point?

This edition of the Fastener Training Minute with Carmen Vertullo was originally published November 21, 2020 as “if you don’t have the point you’re going to get the point” during episode 158 of Fully Threaded Radio. Hello everyone. This is Carmen Vertullo with your Fastener Training Minute coming to you from the Fastener Training Institute […]

Read More… from FTM 158: What’s the Point?

FTM 157: Thread Stick-Out

This edition of the Fastener Training Minute with Carmen Vertullo was originally published October 18, 2020 as “Thread Stick-Out” during episode 157 of Fully Threaded Radio. Todays Fastener Training Minute comes by way of an email from one of our clients, and that email had to do with a question about “thread stick-out“. Now “Stick-Out” […]

Read More… from FTM 157: Thread Stick-Out

FTM 155: ASME B1.3 System 22 Thread Gauging

Fastener Training Minute episode 155, Tri-Roll measurement gauge

This edition of the Fastener Training Minute with Carmen Vertullo was originally published August 15, 2020 as “System 22 thread gauging or thread inspection” during episode 155 of Fully Threaded Radio. I got a question or a suggestion recently from one of our good friends, Baron Yarbrough from Spring Bolt & Nut. Baron asked if […]

Read More… from FTM 155: ASME B1.3 System 22 Thread Gauging